东莞移印机在使用过程中难免会存在一些毛病问题,如手动、半主动悉数不动作,或许电源灯亮、印刷座左移后便不动作等等,咱们有必要熟悉形成这些毛病的原因,才干将问题解决,才干印刷流程顺利进行,因此文中总结了11种丝印机常见的毛病和解决办法.

       第一种现象:半主动时未踩脚踏开关而当即动作.

原因:脚踏开关损坏或脚踏开关插座进水导致短路,或手动起动按钮开关有问题.解决办法是替换新的开关、插座、按钮开关或拆开修理相关损坏件.

      第二种现象:半主动作业时踩脚踏开关滑座下降,铺开后又上升.

原因:横滑座左边挨近开关损坏或断了连线.解决方法是替换挨近开关或接通开关连线.

      第三种现象:半主动作业时踩脚踏开关立滑座下降,印刷座左移后即不动作.

原因:横滑座左边挨近开关未感应到或有问题.解决方法是调整好左边挨近开关感应点或替换好的挨近开关;或许脚踏开关内微动开关卡住不动作,也会引起此毛病.解决方法是将脚踏开关内的微动开关调整、修正或替换新的微动开关.

      第四种现象:半主动作业时踩脚踏开关,滑座下降左移后上升但不右移.

原因:立滑座左上方挨近开关未感应到或挨近开关有问题,解决方法是调整上方挨近开关感应或更好的挨近开关.

     第五种现象:动作切换后上升动作慢半拍.

原因:操控电磁阀有异物堵塞或电磁阀有毛病,解决办法是拆除磁阀整理或替换好的电磁阀.

      第六种现象:手动、半主动悉数不动作,电源灯亮.

原因:有低压侧保险丝烧断,无气源进入,电磁阀悉数都有毛病.解决方法是换低压侧保险丝,查看压力是否到达4-7kg/cm,电磁阀悉数毛病很小,多半是连线断.

      第七种现象:主动、半自发动不下降.

原因:横滑座右侧挨近开关有毛病或未感应到、选择开关毛病、单动开关连锁点损坏.解决方法是调整挨近开关感应或替换右侧挨近开关,替换或修正选择开关及单动开关.

      第八种现象:主动无法发动 .

原因:上、下气缸的微支开关常闭,接点无法导通或计时器损坏,解决方法是修正微动开关,或替换好计时器.

      第九种现象:作业台面不吸气.

原因:吸气马达烧了.操控马达运行的接触器损坏、吸气马达滚动,但操控吸气电磁阀毛病、吸气选择开关毛病,解决方法修正或替换.

      第十种现象:作业台面不吸气.

原因:是吸所操控电磁阀坏或内部块损坏,解决方法是替换修正.

      第十一种现象:立滑座上升速度缓慢.

原因:立滑座轴承无油或气缸活塞磨损,磁撞使轴心弯曲,解决方法是补给油、替换活塞口令,调整轴心.

    以上就是东莞移印机在使用过程中遇到的一些问题和解决方法，还有什么不明白的可以访问我们忠科移印机的官网http://www.chungfouyy.com.cn/

   Dongguan printing machine will inevitably have some problems in the process of using, such as manual, semi active full action, perhaps the power light, printing seat left after no action and so on, we need to understand the causes to these problems, solve the ability, to the printing process smoothly, so this paper summarizes 11 kinds of common problems and solutions of screen printing machine.

The first phenomenon: not stepping on the foot switch at the time of semi-active.

Cause: foot switch damage or foot switch socket inlet leads to short circuit, or manual start button switch is problematic. The solution is to replace new switches, sockets, button switches or disassemble repair related damaged parts.

The second phenomenon: the sliding seat of the foot switch drops in the semi-active operation, and then rises after the opening.

The reason: the left seat slide switch is damaged or broken up. The solution is to replace the wired switch or switch on the line.

Third kinds of phenomena: the foot switch stand slide seat falls in the semi-active operation and the printing seat will not move after the left shift.

The reason: the left seat slide switch is not sensitive to near or problems. The solution is to adjust to the left switch induction point or replace the proximity switches the pedal switch; perhaps micro switch is stuck not action, can also cause this problem. The solution is to adopt the micro switch to adjust, amend or replace the new micro switch foot switch.

Fourth kinds of phenomena: step on the foot switch during the semi-active operation, the sliding seat drops to the left and then rises, but does not move right.

Reason: the upper left of the vertical sliding seat is close to the switch or close to the switch. The solution is to adjust the upper proximity switch induction or better close to the switch.

Dongguan printing machine product map

Fifth phenomena: action after switching the rising action slow.

Reason: the control of the solenoid valve has a foreign body blockage or the electromagnetic valve has a fault, the solution is to dismantle a magnetic valve or replace a good solenoid valve.

Sixth kinds of phenomena: manual, semi-active and no action, power lamp light.

The reason is: there is a low voltage side fuse, no gas inlet, and all the solenoid valves are defective. The solution is to change the low-side side fuse to see whether the pressure reaches 4-7kg/cm, and the solenoid valve is very small, most of which are connected.

The seventh phenomenon: the initiative, the half self start does not decline.

The reason: the right to a faulty switch slide seat or not to switch, induction switch faults and single chain damage. The solution is to adjust or replace the right to switch induction switch, replacement or correction of switch and single switch.

The eighth phenomenon: the initiative can not be launched.

Reason: the micro branch switch of the upper and lower cylinders is often closed, the contact can not be guided or the timer is damaged. The solution is to correct the micro switch or replace the timer.

The ninth phenomenon: the work table is not aspirated.

The reason is: the suction motor is burnt. It controls the motor's contactor damage and the suction motor rolling, but controls the suction solenoid valve's trouble and aspiration to select the switch fault, so that the solution can be corrected or replaced.

The tenth phenomenon: the work table is not aspirated.

Reason: the solenoid valve is damaged or the internal block is damaged by the suction operation. The solution is the replacement correction.

The eleventh phenomenon: the vertical sliding seat has a slow rise.

Reason: no oil or cylinder piston wear of the bearing of the vertical sliding seat. The magnetic collision causes the axis to bend. The solution is to recharge the oil, replace the piston order and adjust the axis.

The above are some problems and solutions encountered in the process of Dongguan pad printing machine. What else do you not understand can access our official website http://www.chungfouyy.com.cn/ of Zhongke pad printing machine?